Product Information
With a boost level of 5 psi and high-volume design, you are sure to get the additional horsepower you are looking for with minimal stress on the motor. Your Polaris Ranger will see a dramatic horsepower increase of up to 94%. This system will fit all 2 door and 4 door Polaris Ranger models with a rear mounted factory exhaust.
HORSEPOWER
- Stock HP - 82hp
- Turbo HP - 159hp calculated
- DYNO NUMBERS
- Stock RWHP - 54hp
- Turbo RWHP - 105hp
- Stock torque - 45 lb-ft
- Turbo torque - 70 lb-ft
TURBO COMPONENTS
Turbo system includes the following:
- Garrett Turbo
- Dynojet Powervision 3 with tune
- Dynojet Wideband AFR controller
- 2.5" aluminum charge tube
- 3" cold air intake
- 4 ply silicone
- Stainless steel high flow turbo supply pipe and exhaust components
- Braided stainless steel supply lines
- All necessary fittings, hoses, clamps, and hardware
*** If your vehicle is going to be used in deep water, or deep mud please upgrade the oil scavenge pump to the waterproof model. ****
Off-Road Use Only
Ask a QuestionQUESTIONS & ANSWERS
Ask a Question-
Do you make a kit for a 2018 Polaris ranger diesel crew? Kholer diesel engine 1028cc
Not at the moment 1-15-2024 we do not make a turo system for the Ranger Diesel. We do not get much call for them.
-
Can ya get a turbo kit for a 2021 Polaris Ranger with a side mount exhaust
Yes, We can make an add-on pipe that will connect the rear-mount turbo system to a side-mount muffler header. There is an extra cost for this product. Give us a call or shoot us an email for pricing.
-
Whats the typical install time and compentcy level required?
The install time on this product is between 10-12 hrs. This is just an estimate. The exact time could be faster or slower depending on the conditions and tools available. You must have basic tools, some knowledge of engine mechanics, and how to set up a turbo vehicle.
-
Does it come with injectors and map sensor? What kind of reliability have you seen on these with stock motors? Any head gasket issues?
Yes this turbo system comes with bigger injectors and a 3-bar map sensor. We have had very good reliability. Your engine is good up to approx. 7 psi. boost pressure above that you will need to add our Ranger water to air charge tube assembly, change the head studs, and put low compression pistons in it. For boost levels over 12 psi you will need to get your crank welded, different connecting rods, and a manual timing chain adjuster. At 12 psi you will be pushing approx 145 RWHP. Turbo systems are typically 3 days to ship.
Will only fit a rear-mounted muffler. Contact us if you have a side-mounted muffler.
Polaris
- Ranger 1000 (2020-2024)
- Ranger Crew 1000 (2020-2024)
- Ranger Crew XP 1000 (2018-2024)
- Ranger XP 1000 (2018-2024)
Performance Expectations
- 94% increase in horsepower and 55% increase in torque
- Stock HP - 82hp
- Calculated Turbo HP - 159hp
- Dyno Numbers
- Stock RWHP - 54hp
- Turbo RWHP - 105hp
- Stock Torque - 45 lb-ft
- Turbo Torque - 70 lb-ft
Tuning
- Base fuel mapping included. Digital fuel controller tuning required for specific machine setup for optimum functionality.
- For diagnostics and tuning, AFR and boost gauges recommended.
Boost Level
- 5psi low-pressure high-volume
Fuel Considerations
- 91 octane non-ethanol fuel is compatible
System Exhaust
- Stainless steel high flow performance resonator
Support
- Our experienced staff is available Monday through Friday from 9am - 5pm MST to assist with any of your technical questions.
Warranty